View FWDM-1629-17_4450719.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Finisar
Preliminary Product Specification
DWDM SFP Transceiver FWDM-1629-XX
PRODUCT FEATURES * * * * * * * * * * Up to 1.25 Gb/s bi-directional data links Hot-pluggable SFP footprint Temperature-stabilized DWDMrated DFB laser transmitter 100GHz ITU Grid, C Band Low dispersion DFB laser suitable Metal enclosure for low EMI Extended operating range: -5C to 70C case temperature Wavelength controlled within 0.1 nm over life and temperature Extended link budget with APD receiver technology GbE and 1X FC compliant * * * APPLICATIONS Amplified DWDM networks Bandwidth aggregation Ring topologies with OADM
Finisar's Dense Wavelength-Division Multiplexing (DWDM) transceivers offer DWDM transport with dramatically lower power and cost in a standard pluggable Small Form Factor Pluggable (SFP) package. The FWDM-1629 is designed expressly for service providers deploying DWDM networking equipment in metropolitan Ethernet and SAN networks. The fiber link budget has been enhanced to 30dB with an Avalanche Photo Diode (APD) receiver. In addition, digital diagnostic features are implemented as described in Finisar Application Note AN-2030, "Digital Diagnostic Monitoring Interface for Optical Transceivers"2.
(c) Finisar Corporation Rev C, February 2005
PRELIMINARY and Confidential
Page 1
Finisar
PRODUCT SELECTION
Product Code FWDM -1629-17 FWDM -1629-18 FWDM -1629-19 FWDM -1629-20 FWDM -1629-21 FWDM -1629-22 FWDM -1629-23 FWDM -1629-24 FWDM -1629-25 FWDM -1629-26 FWDM -1629-27 FWDM -1629-28 FWDM -1629-29 FWDM -1629-30 FWDM -1629-31 FWDM -1629-32 FWDM -1629-33 FWDM -1629-34 FWDM -1629-35 FWDM -1629-36 FWDM -1629-37 FWDM -1629-38 FWDM -1629-39 FWDM -1629-40 FWDM -1629-41 FWDM -1629-42 FWDM -1629-43 FWDM -1629-44 FWDM -1629-45 FWDM -1629-46 FWDM -1629-47 FWDM -1629-48 FWDM -1629-49 FWDM -1629-50 FWDM -1629-51 FWDM -1629-52 FWDM -1629-53 FWDM -1629-54 FWDM -1629-55 FWDM -1629-56 FWDM -1629-57 FWDM -1629-58 FWDM -1629-59 FWDM -1629-60 FWDM -1629-61 Frequency (THz) 191.7 191.8 191.9 192.0 192.1 192.2 192.3 192.4 192.5 192.6 192.7 192.8 192.9 193.0 193.1 193.2 193.3 193.4 193.5 193.6 193.7 193.8 193.9 194.0 194.1 194.2 194.3 194.4 194.5 194.6 194.7 194.8 194.9 195.0 195.1 195.2 195.3 195.4 195.5 195.6 195.7 195.8 195.9 196.0 196.1 Center Wavelength (nm) 1563.86 1563.05 1562.23 1561.42 1560.61 1559.79 1558.98 1558.17 1557.36 1556.55 1555.75 1554.94 1554.13 1553.33 1552.52 1551.72 1550.92 1550.12 1549.32 1548.51 1547.72 1546.92 1546.12 1545.32 1544.53 1543.73 1542.94 1542.14 1541.35 1540.56 1539.77 1538.98 1538.19 1537.40 1536.61 1535.82 1535.04 1534.25 1533.47 1532.68 1531.90 1531.12 1530.33 1529.55 1528.77
(c) Finisar Corporation Rev C, February 2005
PRELIMINARY and Confidential
Page 2
FWDM-1629-XX DWDM SFP Preliminary Product Specification - February 2005
Finisar
I.
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Pin Descriptions
Symbol VEET TFAULT TDIS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select LOS VEER VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault Transmitter Disable. Laser output disabled on high or open Module Definition 2. Data line for Serial ID Module Definition 1. Clock line for Serial ID Module Definition 0. Grounded within the module No connection required Loss of Signal indication. Logic 0 indicates normal operation Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. 100 ohm termination between TD+ and TD-, AC Coupled thereafter Transmitter Inverted DATA in. See TD+ Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 3 3 4 5 1 1 1
1
1
1
Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 5.5V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. Finisar 2x receiver achieves simultaneous 1x and 2x operation without active control. 5. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 5.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
VeeT 1 2 3 4 VeeT TDTXFault TD+ TX Disable VeeT MOD-DEF(2) VccT
20 19 18 17 16 15 14 13 12 11
Towards Bezel
5 6 7 8 9 10
MOD-DEF(1) VccR MOD-DEF(0) VeeR Rate Select RD+ LOS RDVeeR VeeR VeeR
Towards ASIC
(c) Finisar Corporation Rev C, February 2005
PRELIMINARY and Confidential
Page 3
FWDM-1629-XX DWDM SFP Preliminary Product Specification - February 2005 Diagram of Host Board Connector Block Pin Numbers and Names
Finisar
II.
Absolute Maximum Ratings
Symbol Vcc TS TOP Min -0.5 -10 -5 Typ Max 4.7 85 70 Unit V C C Ref.
Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature
III.
Electrical Characteristics (TOP = -5 to 70 C, VCC = 3.13 to 3.50 Volts)
Symbol Vcc Icc Isurge Pmax Rin Vin,pp VD VEN Vout,pp tr tf VLOSfault VLOS norm PSR Min 3.13 Typ 3.30 Max 3.50 305 Icc+30 1.0 Unit V mA mA W mV V V mV ps ps V V mVpp Ref.
Parameter Supply Voltage Supply Current Inrush Current Maximum Power TRANSMITTER Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage RECEIVER Single ended data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Notes: 1. 2. 3. 4. 5. 6.
100 250 Vcc - 1.3 Vee 175 1200 Vcc Vee+ 0.8 1000 150 150 VccHOST Vee+0.5
1
2 3 4 4 5 5 6
Vcc - 0.5 Vee 100
Connected directly to TX data input pins. AC coupled thereafter. Or open circuit. Into 100 ohms differential termination. 20 - 80 % Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network.
(c) Finisar Corporation Rev C, February 2005
PRELIMINARY and Confidential
Page 4
FWDM-1629-XX DWDM SFP Preliminary Product Specification - February 2005
Finisar
IV.
Low Speed Signals
Symbol Min -42 0.5 t_loss_on t_loss_off t_off Typ -36 -34 2 Max Units Notes/Conditions dBm dBm dB sec From detection of loss of signal to assertion of RX_LOS sec From detection of presence of signal to negation of RX_LOS sec Rising edge of TX_DISABLE to fall of output signal below 10% of nominal Falling edge of TX_DISABLE sec to rise of output signal above 90% of nominal. Time indicated is under steady-state temperature conditions. sec TX_DISABLE HIGH before TX_DISABLE set LOW nm TX_Fault will assert before the device is outside of specified wavelength range
Parameter RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay RX_LOS Negate Delay TX_DISABLE Assert Time
-32 100 100 10
TX_DISABLE Negate Time
t_on
1000
TX_DISABLE Reset Time TX_FAULT Assert
t_reset
10 -0.2 +0.2
(c) Finisar Corporation Rev C, February 2005
PRELIMINARY and Confidential
Page 5
FWDM-1629-XX DWDM SFP Preliminary Product Specification - February 2005
Finisar
V.
Parameter
Optical Parameters
Symbol Min Typ Max Units Notes/Conditions
TRANSMITTER CHARACTERISTICS Center Wavelength Spacing Spectral Width Transmitter Center Wavelength - End of Life Transmitter Center Wavelength - Start of Life Side Mode Suppression Ratio (SMSR) Optical Rise/Fall Time Transmitter Optical Output Power Transmitter Extinction Ratio Transmitter Eye Opening 20 c c SMSR tr / tf Pout OMI X - 100 Y - 25 30
100 0.2 X Y 0.3 X + 100 Y + 25
GHz nm pm pm dB 200 +4
Corresponds to approximately 0.8 nm Full width, -20dB from max X = specified center wavelength Y = X - 60pm Modulated
0 9.0 40
Relative Intensity Noise Dispersion Penalty at 180km RECEIVER CHARACTERISTICS Optical Input Wavelength Receiver Jitter Generation Optical Input Power (BER < 10 -9) Optical Input Power (BER < 10 -12) Optical Input Power - Receiver Damage Threshold Receiver Reflectance OSNR Limit OSNR Penalty
RIN
-120 3.0 1520 1570 100
ps Unfiltered, 80% -20% dBm Average power coupled into single mode fiber dB % IEEE 802.3 and Fibre Channel Eye Mask Margin dB/Hz dB 3600ps/nm. See Note 3. nm Peak to peak, -25 dBm Rx power dBm 1.25 Gb/s w/ PRBS 2 7 -1 dBm 1.25 Gb/s w/ PRBS 2 7 -1 dBm dB dB dB ps
Pin
Pin Pin
-32 -30
-9 -9 6
RRX OSNRmin 20
-27
2.0
For OSNR = OSNRmin. See Note 4.
Notes: 1. Parameters are specified over temperature and voltage, at end of life unless otherwise noted. 2. All parameters are measured on a Finisar SFP Evaluation Card unless otherwise noted. 3. Dispersion penalty is measured in loop back with OSNR set at Rx < 28 dB. Data rate and pattern used same as specified for Optical Input Power. Dispersion penalty is measured at BER = 10-10 4. OSNR penalty is measured in loop back. Data rate and pattern used is same as specified for Optical Input Power. OSNR penalty is measured at BER = 10-10
(c) Finisar Corporation Rev C, February 2005
PRELIMINARY and Confidential
Page 6
FWDM-1629-XX DWDM SFP Preliminary Product Specification - February 2005
Finisar
VI. Wavelength Stabilization The laser transmitter will not be turned on until its temperature is adjusted to ensure operation within the specified channel (X +/- 0.4nm). This temperature stabilization time is dependent on the ambient temperature conditions, but will typically occur within 90 seconds of powering the device. The device will transmit within the specified wavelength tolerance (X +/- 0.1nm) within 5 seconds of transmitter operation.
VII. General Specifications
Parameter Data Rate Symbol BR Min 1.06 1.25 Max 1.25 Units Notes/Conditions
Gb/sec Fibre Channel, IEEE 802.3 compatible Total System Budget 30 32 dB @ 1.25 Gb/s, BER <10-12 w/ PRBS 2-7-1. See Note 1 Note 1: Total system budget is defined as Pout - Pin - typical connector losses.
VIII. Environmental Specifications
Parameter Operating Temp Symbol Top Min -5 Typ Max 70 Units Notes/Conditions C
Case temperature measured on top-side of device Storage Temp Tsto -10 85 C Ambient temperature Eye Safety CDRH and IEC-825 Class 1 Laser Product. See Note 1 Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001.
(c) Finisar Corporation Rev C, February 2005
PRELIMINARY and Confidential
Page 7
FWDM-1629-XX DWDM SFP Preliminary Product Specification - February 2005
Finisar
IX. Serial Communication Protocol All Finisar SFPs support the 2-wire serial communication protocol outlined in the SFP MSA1. These SFPs use an Atmel AT24C01A 128 byte E2PROM with an address of A0h. For details on interfacing with the E2PROM, see the Atmel data sheet titled "AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM."4 Finisar's DWDM SFPs also support extended diagnostic features as described in Finisar Applications Note AN-2030, "Digital Diagnostic Monitoring Interface for Optical Transceivers"2. A controller IC that monitors system parameters such as laser current, module temperature, transmitter power, and received power is accessible at address A2H.
Parameter I2C Clock for Atmel (A0H) and Controller IC (A2H)
Symbol Catmel
Min 0
Typ
Max 100,000
Units Notes/Conditions Hz Bus can be driven blind.
( E2PROM Description TBD pending MSA)
(c) Finisar Corporation Rev C, February 2005
PRELIMINARY and Confidential
Page 8
FWDM-1629-XX DWDM SFP Preliminary Product Specification - February 2005
Finisar
X.
Mechanical Specifications
Finisar's Multi-rate DWDM Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA).
Figure 1. DWDM SFP Outline Drawing
(c) Finisar Corporation Rev C, February 2005
PRELIMINARY and Confidential
Page 9
FWDM-1629-XX DWDM SFP Preliminary Product Specification - February 2005
Finisar
XI. Ordering Information Part Number FWDM-1629-XX Description DWDM SFP with APD Receiver XX = channel number (see product selection on page 2)
XII. References 1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available from Finisar upon request. 2. "Application Note AN-2030: Digital Diagnostic Monitoring Interface for Optical Transceivers", Finisar Corporation, April 2002.
3. "AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM", Atmel Corporation. www.Atmel.com 4. "Digital Diagnostic Monitoring Interface For Optical Transceivers Rev 6.1", September, 2004. Documentation is currently available from Finisar upon request.
For More Information: Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. (408) 548-1000 Fax (408) 541-6138 sales@finisar.com www.finisar.com
(c) Finisar Corporation Rev C, February 2005
PRELIMINARY and Confidential
Page 10

▲Up To Search▲

Price & Availability of FWDM-1629-17

	To Download FWDM-1629-17 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .